Free Shipping on All U.S. Orders
16% OFF Sitewide Code: BFCM2616
16%OFF
SITEWIDE
USE CODE
BFCM2616
Ends in
00 d
:
00 h
:
00 m
:
00 s

How to Install LED Headlight Bulbs on a 2016–2023 Toyota Tacoma

Alex Thompson |

Installing LED headlight bulbs on a 2016–2023 Toyota Tacoma with factory halogen headlights can be straightforward when you have the correct bulbs and know where to access them.

In this step-by-step Tacoma LED headlight installation guide, we'll show you how to replace the factory low- and high-beam bulbs without removing the headlight assemblies or modifying the factory wiring.

For the LED bulbs shown here, simply align the three mounting tabs, twist the bulb clockwise to lock it, and reconnect the factory plug. The LED chips should face 3 and 9 o'clock, with the power cable pointing downward at 6 o'clock.

2016–2023 Toyota Tacoma Headlight Fitment: H11 Low Beam & H9 High Beam

Before starting your Tacoma headlight bulb replacement, confirm your truck's factory lighting configuration.

This guide applies to 2016–2023 Toyota Tacoma models with replaceable factory halogen headlight bulbs. If your Tacoma has factory LED headlamps, refer to the appropriate Toyota service procedures. For aftermarket headlight housings, follow the bulb specifications provided by the housing manufacturer.

Toyota Tacoma Factory Halogen Bulb Sizes

Headlight Position Factory Halogen Bulb Size
Low Beam H11
High Beam H9

Toyota lists these sizes for bulb-type headlights. Check your model year, trim, headlight type, and the markings on the bulb you’re replacing before choosing an LED kit. 2016 Tacoma Owner’s Manual, p. 578 · 2023 Tacoma Owner’s Manual, p. 553


What about H11/H8/H9 LED bulbs?

Some aftermarket LED products are designed for multiple bulb applications. For example, Lasfit offers LS Plus H11/H8/H9 LED bulbs for selected compatible applications.

However, the H11/H8/H9 designation describes the LED product's fitment range, not the Toyota factory halogen specification. Always verify your Tacoma's model year, trim, original headlight type, and replacement bulb markings before choosing an LED kit.

Before You Open the Hood

Before replacing your Tacoma headlight bulbs, follow these basic preparation steps:


  1. Park safely. Park on level ground and engage the parking brake.
  2. Record the original beam pattern. If you plan to compare the lighting afterward, photograph the factory low beams against a flat wall. Keep the truck in the same position for the final check.
  3. Turn everything off. Switch off the engine and headlights, then allow the bulbs to cool completely.
  4. Handle bulbs carefully. Wear clean gloves and hold each bulb by its base. Avoid touching the halogen glass or LED chips.

Preparing a Toyota Tacoma for LED headlight bulb installation

Locate the Low- and High-Beam Bulbs on Your Tacoma

The plug-and-play bulb installation demonstrated here requires no hand tools.

Open the hood and locate the low-beam and high-beam sockets behind the driver's-side headlight assembly, as shown below.

Both bulbs can be accessed from behind the headlight. After completing the driver's side, repeat the procedure on the passenger side.

Low- and high-beam bulb socket locations behind the driver-side Toyota Tacoma headlight

Low- and high-beam sockets behind the driver's-side headlight.

How to Replace Toyota Tacoma H11 Low-Beam Bulbs

Follow these five steps to remove the factory H11 low-beam bulb and install the compatible LED replacement shown in this guide.

Step 1: Disconnect the Factory Low-Beam Connector

Locate the electrical connector behind the factory low-beam bulb.

Press the release tab and pull the connector straight down by its plastic body. Avoid pulling directly on the wiring.

Releasing the factory Tacoma low-beam connector

Step 2: Remove the Factory Halogen Bulb

Grip the original H11 bulb by its base.

Turn it counterclockwise to unlock it, then carefully pull it straight out of the headlight housing.

Step 3: Match the Three Mounting Tabs

Before inserting the replacement LED bulb, align its three mounting tabs with the corresponding slots in the low-beam socket.

All three tabs must line up correctly for the bulb to sit flush. Never force the bulb into the housing.

Caption: Step 3 — Three mounting tabs and corresponding housing slots.

Three LED bulb mounting tabs aligned with Tacoma housing slots

Step 4: Install and Lock the LED Bulb

Insert the LED bulb straight into the socket and turn it clockwise until securely locked.

For the specific LED bulb design demonstrated here, the two LED chips should face horizontally:


  • 3 o'clock: One chip faces left.
  • 9 o'clock: The other chip faces right.
  • 6 o'clock: The power cable points downward.

This orientation applies to the bulbs shown in the tutorial. Other LED designs may require different adjustments, so follow the selected product's instructions.

Clockwise locking direction for the Tacoma LED headlight bulb

Step 5: Reconnect the Plug and Route the Cable

Align the keyed connector halves and press them together until fully seated.

Gently tug the plastic connector body to confirm the connection is secure.

Route the cable downward at 6 o'clock, keeping it away from hot surfaces, sharp edges, and moving components.

Repeat the same steps on the passenger-side low beam.

Caption: Step 5 — Keyed factory connector.

Keyed factory connector for the Tacoma LED headlight bulb

How to Replace Toyota Tacoma H9 High-Beam Bulbs

The high-beam replacement process is similar to the low-beam installation, but the applicable factory halogen bulb specification is H9.

Step 1: Remove the Factory High-Beam Bulb

Locate the high-beam socket behind the headlight.

If the connector is easy to reach, press its release tab and disconnect it first.

If access is tight, carefully turn the original bulb counterclockwise and pull it out just far enough to reach the release tab without straining the factory wiring.

Remove the bulb from the housing.

Counterclockwise removal of the factory Tacoma high-beam bulb

Step 2: Align the Tabs and Lock the LED Bulb

Line up all three mounting tabs on the compatible replacement LED bulb with the high-beam socket.

Insert the bulb fully and turn it clockwise until locked.

For the bulbs demonstrated here, the LED chips should face left and right at 3 and 9 o'clock.

Three mounting tabs and matching Tacoma high-beam socket slots

Step 3: Reconnect the Factory Plug

Press the factory connector halves together until fully seated.

Route the cable downward at 6 o'clock and keep it clear of hot surfaces, sharp edges, and moving parts.

Repeat the same procedure on the passenger-side high beam.

Test Your Tacoma LED Headlights and Check the Beam Pattern

After installing both low- and high-beam bulbs, test the lighting system while your Tacoma remains parked.

First, switch on the low beams and confirm that both sides illuminate.

If you photographed the original beam pattern, compare the new low beams against the same wall. Look for obvious light scatter, uneven illumination, or changes in the cutoff pattern.

Next, switch to the high beams and confirm that both sides work correctly.

Common Tacoma LED Headlight Installation Problems

What You Notice What to Check
One bulb stays dark Turn off the headlights, reseat the connector, and retest. If the problem continues, verify product compatibility and installation instructions.
The bulb won't turn or lock Remove it, check that all three tabs align with the slots, and try again with the bulb seated flat.
The low-beam pattern looks uneven Turn off the headlights, confirm that the bulb is fully seated, and check the LED chip orientation specified by the manufacturer. Compare the beam against the wall again.

If the problem persists, consult the bulb manufacturer's installation guide or seek professional assistance.

A wall check can help identify obvious mounting or alignment problems, but it does not establish road-use compliance.

Watch: 2016–2023 Toyota Tacoma LED Headlight Installation

Want to see the installation steps in action?

Watch the Toyota Tacoma LED headlight installation video below for a visual walkthrough of the factory bulb removal, mounting-tab alignment, bulb installation, and electrical connections.

Watch the Toyota Tacoma LED Headlight Installation Video

Tacoma LED Headlight Installation FAQs

How Many LED Bulbs Do I Need for Both Low and High Beams?

You need four bulbs to replace both beam positions on a third-generation Tacoma equipped with separate factory halogen low- and high-beam bulbs.

Use two bulbs for the low beams and two for the high beams. If you're changing only one lighting position, you need one pair.

Can I Use the Same LED Bulb for the H11 Low Beam and H9 High Beam?

Some multi-fit LED bulbs can work in both applications if the manufacturer specifically lists them as compatible. For example, the Lasfit LS Plus H11/H8/H9 Series supports selected H11 and H9 applications. Remember that Toyota's factory halogen specifications are H11 for low beam and H9 for high beam. Always confirm the exact product fitment before purchasing.

Do I Need to Remove the Tacoma Headlight Assembly or Splice Wires?

No. The plug-and-play installation demonstrated here uses the sockets behind the factory headlight assemblies and connects to the existing electrical plugs. Both headlight assemblies stay in place, and the original wiring remains intact.

What Is the Correct LED Bulb Orientation on a 3rd Gen Tacoma?

For the LED bulbs shown in this guide, the chips should face horizontally at 3 and 9 o'clock, with the power cable directed downward at 6 o'clock. Always check the instructions for your particular LED bulb, as other designs may require a different orientation.

Does This Installation Work on Tacomas with Factory LED Headlights?

No. This tutorial is intended for 2016–2023 Tacoma models equipped with replaceable factory halogen headlight bulbs. Factory LED headlamp assemblies may use different components and service procedures. Check your vehicle's original lighting system before ordering replacement parts.

Final Tips for Your Tacoma LED Headlight Installation

Replacing the bulbs on a factory-halogen third-generation Tacoma involves a few straightforward steps: locate the sockets, disconnect the original bulbs, align the replacement mounting tabs, lock the bulbs in place, and reconnect the factory plugs.

The most important details are correct bulb fitment, secure mounting, proper cable routing, and a final beam-pattern check.

If you're comparing compatible bulb options for permitted applications, explore Lasfit's 2016–2023 Toyota Tacoma LED Lighting Options and verify the selected configuration before purchasing.

Installation photos: Lasfit. Always follow the installation instructions for your specific product and applicable road-use requirements.

Alex Thompson

Alex Thompson is a Senior Product Specialist and automotive lighting tech blogger at Lasfit. With over 8 years of product development experience in the automotive aftermarket industry, he is dedicated to helping vehicle owners find their perfect upgrade through in-depth product reviews and practical installation guides, empowering them to enhance their driving experience safely and effectively.

Leave a comment

    1 out of ...